Welcome back my fellow hackers! Today we’re going to be starting a series that I’ve been meaning to start for some time now. We’re going to start discussing exploitation. As hackers, exploitation is a very large part of our job. Once we find the vulnerabilities, we need to exploit them. We’ve already covered some aspects of exploitation in the past, so if you’re not up to speed I suggest starting with those.
First we’ll talk about some terms that get thrown around a lot when talking about exploitation. I’m just going to make a list of the terms, followed by their definition. These terms are going to be used a lot later in this series, so you should really make sure you understand these terms. If you need help, leave a comment or e-mail me at email@example.com. I’ll try my best to help you get a better grasp on these terms, as they are very important.
- Exploit: An exploit is simply a program/script designed to take advantage of a security flaw. There are many different kinds of exploits, but that is beyond the scope of this introduction. That being said, we’ll cover the more specific types of exploits later in this series.
- Local exploit: A local exploit is an exploit that only works when run locally on the target. These are often used to gain more privileges once initial access to the target system is gained. If the attacker is attempting to physically access the target system, these can be used to easily and quickly gain complete control over the system.
- Remote exploit: A remote exploit is an exploit that works when fired over a network. These are usually used to gain initial access to a system, while local exploits are normally used to gain privileges once basic access to the system of obtained.
- Privilege escalation exploit: This exploit type is just as it sounds. These exploits are specifically designed to exploit vulnerabilities that will yield a higher level of privileges to the attacker (Ex: system services, firmware flaws, poor system configuration). If these exploits are successful, the attacker can attain absolute control over the target system.
- Zero-day exploit: These are the trump cards of hacking. A zero day exploit is an exploit that has never been seen before. Naturally, since the vulnerability is unknown, the exploit is extremely difficult to detect and even harder to stop.
- Payload: Exploits aren’t magic. While they can open opportunities to execute code, there still needs to be code to execute. This is where payloads come in. A payload is simply the code that is executed upon exploitation. A good metaphor for this is a bomber plane. The pilot (attacker) uses the plane (exploit) to get in place in order to drop the bomb (payload). The plane simply puts the pilot in position so that the bomb can be dropped. The same concept applies to us hackers. The exploits simply put is in position to execute the payload. There are many different kinds of payloads, but we won’t get into that just yet.
- Stager: Stagers are important so read this part really carefully. In order for payloads to execute, they have to be stored in the memory of the system. When we exploit a program, we have a very limited amount of memory to store the payload in. Because of this, we often won’t have enough room in memory to store the entire payload. This is why we have stagers. Stagers are a sort of payload. A stager is a payload that will download and execute a larger payload. It’s a payload that downloads and executes another payload, simple enough, right? Since a stager’s only job is to fetch a larger payload, we can use them where we don’t have enough memory to work with. If the payload is too large to fit into the memory available to us, we can use a stager instead. This allows us to work around memory limitations to deliver our payload to the target.
- Post exploitation: After a vulnerability is found and exploited, we’ll have access to the target system. But now what? Well that’s where post exploitation comes into play. Post exploitation is all the stuff we do after we gain access. This includes everything from extracting sensitive information to installing a software key logger. Everything that is done after access (and higher privileges) are gained is considered post exploitation.
- FUD (Fully UnDetectable): This term is not exclusive to exploitation. It is also used a lot when discussing malware (viruses, worms, trojans, etc.). This term mainly applies to payloads, as the payload is the code that is actually executed as the result of an exploit. FUD simply means that the malicious code is fully undetectable by any anti-virus software that may be present on the target system. For example, if you know that your target is running up-to-date anti-virus, you might want to take a look into making your payload FUD. Truly FUD payloads are difficult to come by, but we can get pretty close. We’ll cover making payloads FUD(ish) later in this series.
- Encoders: Anti-virus developers aren’t stupid, they know what we hackers are up to. Every piece of software has a signature. Anti-virus can use these signatures to spot and remove known malware. Payloads also have a signature, seeing as they’re just small bits of malicious code. This means that anti-virus can detect and stop our payloads from running, and that can be a big problem! Encoders can take our payload and change the way it looks by encoding it. When we encode a payload, the signature changes, so by using encoders, we stand a better chance of sneaking past that pesky anti-virus!
Wow, that was a mouthful! That’s a lot of information to digest so I’m going to cut this off here. In the next article we’ll be introducing some common exploitation tools, such as Metasploit. But before we get there, you should really have a good grasp on everything we talked about here. Remember, if you need clarification on anything, leave a comment or e-mail me at firstname.lastname@example.org and I’ll do my best to help you!